How to make the fl studio asio stop lagging

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING HOW TO#
#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING DRIVERS#
#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING SOFTWARE#
#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING CODE#
#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING WINDOWS#

To conclude about your problem, you should try to minimise the value shown in the second picture until you get the lowest latency values without getting dropouts (clicks and glitches). DSD has certain advantages against PCM like noise-shaping and ease of hardware manufacturing, while it has some drawbacks related to the unbounded error due to the summation operation (I do not provide references here but a quick search on IEEE or AES would provide some papers on all of those topics). Please keep in mind that this is a very vague explanation of each technique and a whole lot of details are omitted (on purpose) here. This one bit is used as the result of a comparison of the current analogue amplitude compared to the one of the previous sample (one if current amplitude is higher, zero if lower) and consequently, the values of 'packets' of samples are summed (this is what the Sigma means in the DSD acronym) and from those a digitised PCM-like value is calculated. Without trying to explain those here (you can create a different question for that, or even better ask at DSP SE), in the former (PCM) samples are taken every 1/sampling-rate and they are quantised based on the bit-depth used (16-bit for CD quality, while 24-bit is quite often seen nowadays) and in the latter (DSD) the sampling rate used is very high (2.8224 MHz in your case as it seems) with one bit of coding.

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING CODE#

The first value of buffer size refers to Pulse Code Modulation ( PCM) coding while the second value refers to Delta Sigma Demodulation ( DSD) coding. It seems that the slider refers to the latency (in ms) and not the buffer size, which may prove to be easier to use for you (since you seek a short delay). Now, regarding the buffer size and latency, it seems that you can tweak those from the panel you present in the second picture. This means that, if your hardware does not support sampling rates other than 44.1 KHz and 48 KHz, then you are stuck with those.

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING DRIVERS#

Additionally, as stated there (in the link), the supported sampling rates depend on the hardware used (and quite rarely on the drivers - most probably this is not an issue nowadays).

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING WINDOWS#

You could possibly do that from the Windows audio control panel as is show in the thread of the link.

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING SOFTWARE#

It seems that the software you are using is not capable of changing the sampling rate or the buffer size used by the drivers. Generally speaking, and without going into too much detail, the rule of thumb on latency values is that the greater the buffer used, the greater the latency from input to output will be (and most probably any other processing related to that). Reading the thread from the link you attached I have to say that those people there explained quite well what is going on and what the possible solutions would be. Your problem is related to the drivers of your sound card as well as to the capabilities your computer has. Hello joshuaronis and welcome to Sound Design SE. If you need any more information please let me know in a comment. I'm sorry my question is a little vague, but I really am a newbie to this stuff, and its all quite confusing. I'd really like to understand what's happening (the difference between the two sample-rates, etc.) and what I should do.ДЄnd, if the solution is the same as it was to my linked question one year ago about the WASAPI drivers, I would appreciate any recommendations, along with an explanation of why that is the only solution.what's wrong with my laptop? It doesn't let me change the 'latency' on this screen, but if I click on ASIO Config, I get this: However, right now there is A LOT of latency, making my drum set unplayable. I have a Roland TD 25 K electric drum set which I'm trying to use to trigger sounds in Kontakt 5 Studio Drummer. I don't quite understand a lot of what's going on, so I'd really, really appreciate detailed baby-like explanations.

#HOW TO MAKE THE FL STUDIO ASIO STOP LAGGING HOW TO#

However, I had to sell my acoustic drum set, and now I'd really like to figure out how to use my electric one. The conclusion in that thread was that I should just get an external interface.but, I didn't even know what those were, and I had already spent a lot of money, so I gave up. However, I had no idea what I was doing, was faced with a problem, and eventually gave up and went back to my acoustic kit.Д®ventually, I found ASIO drivers and installed them on my laptop (not just ASIO4All drivers).

How to make the fl studio asio stop lagging